Wall Mounted Penstock
The Wall mounted penstock is a rectangular stainless steel frame structure. The driving device is installed on the beam of the gate frame, and the door frame is installed on both sides of the pool wall. Door panels, door frames, guide rails, screws and driving devices should...Send Inquiry
The Wall mounted penstock is a rectangular stainless steel frame structure. The driving device is installed on the beam of the gate frame, and the door frame is installed on both sides of the pool wall. Door panels, door frames, guide rails, screws and driving devices should have sufficient strength and rigidity, and their tensile, compression and shear strength safety factors should be greater than 5 to ensure the normal operation of the equipment.
Material of main parts
Door panel, door frame, guide rail, gate screw: stainless steel
Sealing strip: Nitrile rubber
Electric device: Changzhou
1. The Wall penstock has sufficient strength, rigidity and tightness
The Stainless steel Wall penstock is provided with a well-shaped rib on one side to increase the strength, and the water facing surface is a flat plate, and the seal of the gate is sealed with rubber. The manual opening and closing device is driven by screw and nut, and the screw is made of stainless steel, which can automatically adjust the swing of the screw during transmission without damaging the seal of the gate.
2. The Wall penstock has anti-corrosion characteristics
Non-metal and non-ferrous metals are not coated with anti-corrosion paint. Before painting, the remaining parts should be cleaned of burrs, oxide scales, rust spots, sticky sand, scars, and oil stains. The gates, risers, fleshy and sharp edges, etc. should be shoveled and sandblasted. The level of surface treatment It is Sa21/2 level.
3. The Wall penstock is light, strong, beautiful in appearance and easy to operate
The Wall penstock structure is made as light, strong, beautiful in appearance and easy to operate as far as possible while meeting the rigidity requirements. If manufacturers have better suggestions and newer products, they can provide options, but they must be confirmed by the owner and engineer. The opening and closing device must be directly installed on the upper part of the mast, and the height should satisfy the manual operation handwheel.
The manual channel gate is not equipped with an electric control box, and the flashlight dual-purpose gate is equipped with an electric control box (made according to the electrical drawing provided by Party A.
Torch dual-purpose opening and closing device
The dual-purpose opening and closing device with flashlight, its protection level is IP55; the opening and closing device has manual/electric function, when switching to manual, its manual operating force is <150N; the opening and closing device has stroke and torque control device; in the opening and closing device Equipped with a moisture-proof heating device to prevent the contact effect of electrical components from being affected by accumulation. The motor is suitable for power supply 380V, 3-phase, 50Hz, and insulation class F. The output speed of the opening and closing device is n=24r/min, and the opening and closing speed ν≈0.25m/min.
Adopt switch type electric actuator
—Special electric device for multi-turn gate
—Squirrel cage induction motor, insulation class F
—Voltage 380V 3P 50HZ, allowable voltage fluctuation ±5%
—Working time S2～15 minutes
—Equipped with 2 limit switches (1 gate position open/1 gate position closed), so that the gate can be limited in any position
—Equipped with 2 torque switches (1 opening position/1 closing position)
-Equipped with a motor overheating protection switch
—Protection level of actuator IP55
—The manual wheel operated in an emergency situation can be automatically disengaged when the motor is started, and the manual wheel is stationary when the motor is running.
-Equipped with mechanical valve position display (gate opening display panel)
—Passive output contacts: open in place, close in place, fault, manual/remote control
—Passive input contacts: open, close
—The output terminal can shift the open and close control signal to the valve body
—Operation selection switch: on-site—off—remote control
-Action button: open-stop-off
—Gate status indicator light (3 lights)
Hot Tags: wall mounted penstock, China, suppliers, manufacturers, factory, customized, price, OEM